From below remove the two black headed philips screws under the fog light location pull the black plastic inner fender liner toward the tire. Watch for the two spring screw clips they may fall off put them back on. now you can see the back of the fog light assembly either the bulb is visiable or the black plastic cover needs to be turned to the left then remove the bulb. do not touch the glass of the new bulb. Skin oils will shorten the life of the new bulb.
How can i change the fog light bulb on 2002 nissan altima?
you have to replace the entire light assembly on that model nissan
How can i change the fog light bulb on 2002 nissan altima?
Smash it with a crow bar and use a screwdriver to pry the pieces out.
Tuesday, September 20, 2011
How do I get to my dash light?
I have a 98' Saturn SC2, my fog lights, tail lights and dash lights were all out, so I changed the fuse and they all work but my dash lights. So I was wondering how do I get in there to change the light so that my car will pass the safety inspection?
How do I get to my dash light?
Check for another blown fuse.
How do I get to my dash light?
Check for another blown fuse.
How to change a bulb in a fog light on a Peugeot 306?
Good luck with that
How to change a bulb in a fog light on a Peugeot 306?
Remove blown bulb and replace with good one!
How to change a bulb in a fog light on a Peugeot 306?
This will take at least 5 cops, 15 lawyers or doctors and 25 politicians.
the bulb comes out from behind the foglight so whatever you have to do or take off to get to it.
How to change a bulb in a fog light on a Peugeot 306?
Remove blown bulb and replace with good one!
How to change a bulb in a fog light on a Peugeot 306?
This will take at least 5 cops, 15 lawyers or doctors and 25 politicians.
the bulb comes out from behind the foglight so whatever you have to do or take off to get to it.
I just bought a 1994 chrysler lhs and I have no high beams and no fog lights.?
I cannot imagine that four bulbs could be out in this thing and nobody bothered to change them so I figure it may be something deeper, also the high beam indicator on the switch does not come on when I pull it so I wonder if the switch would cause it or if it would be something else. I checked the fuse and yes that is ok.
I just bought a 1994 chrysler lhs and I have no high beams and no fog lights.?
you may have a bad multi-function switch. the one you use to activate your high beams.
I just bought a 1994 chrysler lhs and I have no high beams and no fog lights.?
multi function swith-almost bet on it
I must aggree with the others. Bad multi function switch. When u go to turn ur hig beams on, ur driving lights or fog light should cancel out. If this switch is bad then it may cause both systems to not work. The multi function switch is the turn signal handle on the left side of the steering wheel. Be careful messing with it yourself because if you have to remove the steering wheel you may set off the air bag. It aint pretty when one goes off in your face, not to mention the damage and expense it costs. have a pro do it
I just bought a 1994 chrysler lhs and I have no high beams and no fog lights.?
you may have a bad multi-function switch. the one you use to activate your high beams.
I just bought a 1994 chrysler lhs and I have no high beams and no fog lights.?
multi function swith-almost bet on it
I must aggree with the others. Bad multi function switch. When u go to turn ur hig beams on, ur driving lights or fog light should cancel out. If this switch is bad then it may cause both systems to not work. The multi function switch is the turn signal handle on the left side of the steering wheel. Be careful messing with it yourself because if you have to remove the steering wheel you may set off the air bag. It aint pretty when one goes off in your face, not to mention the damage and expense it costs. have a pro do it
Which is the best super yellow or white bulb for the 08 GS350 fog light to match the headlight white color?
I was wondering if anyone can help me on this? Which is the best fog light bulb replacement to match the headlight color (white)? or is there a super bright yellow that's brighter than the stock (faded yellow)? Can i just change the bulb or do i have to do a conversion to a HID?
Which is the best super yellow or white bulb for the 08 GS350 fog light to match the headlight white color?
White bulb...small myspace tv card4
Which is the best super yellow or white bulb for the 08 GS350 fog light to match the headlight white color?
White bulb...
1996 Grand Prix flasher units, gauge, head and fog lights, and transmission...?
need to change flasher units for the signals and maybe the hazards...where are they?
also, i think a light in my instrument panel is blown, as the fuel gauge is much dimmer than the others in the dark...how hard is it to get at these bulbs?
...is there a way to decloud my head and fog lamps? i dont want to have to repolish them every 2 months...
finally, the transmission shifts very hard from 1-2, especially under heavy throttle. it pulls sharply to the left on the shift. is this just torque steer, or am i looking at replacing a halfshaft in a few thousand miles?
1996 Grand Prix flasher units, gauge, head and fog lights, and transmission...?
The flasher unit is located under the dash near the steering column. The turn signal flasher is circular . When i comes to the instrument panel being dim. There is multiple light bulbs in the panel. Remove the trim around the panel and then remove the screws holding the panel in. disconnect cannon plugs. Then you see the socket holding the bulbs in. !/4 turn counter clockwise and then remove , install new bulb and reinstall .Comes to the tranny have it power flushed it solves allot of problems. Headlight your local autoparts has what you need
1996 Grand Prix flasher units, gauge, head and fog lights, and transmission...?
the flasher unit is gunna be under the hood and a big black or gray unit.... the bulbs are really easy to get at autozone but a pain to have to put in most likely the whole dash has to come out to pt them in,,, the headlight issues would be better to replace them once they get water soaked or fog up the only way is to put some glue between the two surfaces.... less trouble to buy a set at a junk yard of not looking to pay brandnew prices....the tranny i would have to leave that to someone else that knows more about them... but to say id say that the pulling is deff torque steer and the tranny may need to be rebuilt... gud luck with that pontiac.....
Sylvania / Bulb - Instrument Panel Light
194R $2.99
also, i think a light in my instrument panel is blown, as the fuel gauge is much dimmer than the others in the dark...how hard is it to get at these bulbs?
...is there a way to decloud my head and fog lamps? i dont want to have to repolish them every 2 months...
finally, the transmission shifts very hard from 1-2, especially under heavy throttle. it pulls sharply to the left on the shift. is this just torque steer, or am i looking at replacing a halfshaft in a few thousand miles?
1996 Grand Prix flasher units, gauge, head and fog lights, and transmission...?
The flasher unit is located under the dash near the steering column. The turn signal flasher is circular . When i comes to the instrument panel being dim. There is multiple light bulbs in the panel. Remove the trim around the panel and then remove the screws holding the panel in. disconnect cannon plugs. Then you see the socket holding the bulbs in. !/4 turn counter clockwise and then remove , install new bulb and reinstall .Comes to the tranny have it power flushed it solves allot of problems. Headlight your local autoparts has what you need
1996 Grand Prix flasher units, gauge, head and fog lights, and transmission...?
the flasher unit is gunna be under the hood and a big black or gray unit.... the bulbs are really easy to get at autozone but a pain to have to put in most likely the whole dash has to come out to pt them in,,, the headlight issues would be better to replace them once they get water soaked or fog up the only way is to put some glue between the two surfaces.... less trouble to buy a set at a junk yard of not looking to pay brandnew prices....the tranny i would have to leave that to someone else that knows more about them... but to say id say that the pulling is deff torque steer and the tranny may need to be rebuilt... gud luck with that pontiac.....
Sylvania / Bulb - Instrument Panel Light
194R $2.99
1995 Mazda 929 head lights will not come on but when i pull back on the light switch the bright lights are on
I changed the bulbs and the relay , the relay clicks when i put it on all the other relays in the relay box clicks but my head light and fog light relays dont . WHAT COULD IT BE?
1995 Mazda 929 head lights will not come on but when i pull back on the light switch the bright lights are on
On most (if not all) cars that have the light switch on the turn stalk, if you pull the stalk to change to high beams, it completes the circuit, causing the lights to flash (even when they are off).
If the brights stay on after the stalk is released, but don't come on normally, I would try replacing the switch. It's not a job for the faint-hearted, so think about taking it to your mechanic. You might check to make sure you don't have a loose ground in the switch before you take it in, but more than likely your light/turn signal switch is toast.
1995 Mazda 929 head lights will not come on but when i pull back on the light switch the bright lights are on
There are two bulbs in the headlight globe - a highbeam and a lowbeam. The lowbeam is burned out.
1995 Mazda 929 head lights will not come on but when i pull back on the light switch the bright lights are on
On most (if not all) cars that have the light switch on the turn stalk, if you pull the stalk to change to high beams, it completes the circuit, causing the lights to flash (even when they are off).
If the brights stay on after the stalk is released, but don't come on normally, I would try replacing the switch. It's not a job for the faint-hearted, so think about taking it to your mechanic. You might check to make sure you don't have a loose ground in the switch before you take it in, but more than likely your light/turn signal switch is toast.
1995 Mazda 929 head lights will not come on but when i pull back on the light switch the bright lights are on
There are two bulbs in the headlight globe - a highbeam and a lowbeam. The lowbeam is burned out.
Can the seats and lights be changed in our car?
we have just bought a Citroen Xsara Picasso lx8v 1.6 2005, we have now seen one but it is a Citroen Xsara Picasso Desire, the seats in this one have armrests as well as front fog lights and more, would i be able to put seats from the desire into the ours also the front fog lights, Thank you. uk
Can the seats and lights be changed in our car?
Yes the seats can be changed easily. There are bolts under the seats that you must take off and boom thats done. With the lights, if your bumper has fogs light holes in it then thats easy to get the wiring and put them in, but if not, you can try 1 of 2 things..
Cuts holes in the lower bumper and wire the lights or buy a bumper with the Fog light implants in them and put them in. Either way you will have to wire the Fog lights.
Can the seats and lights be changed in our car?
Yes the seats can be changed easily. There are bolts under the seats that you must take off and boom thats done. With the lights, if your bumper has fogs light holes in it then thats easy to get the wiring and put them in, but if not, you can try 1 of 2 things..
Cuts holes in the lower bumper and wire the lights or buy a bumper with the Fog light implants in them and put them in. Either way you will have to wire the Fog lights.
How do you change front fog light bulbs on 2005 vw golf tdi 2.0?
a google search nets this result:
http://www.golfmkv.com/forums/showthread鈥?/a>
seems like you'll need a torq screwdriver
How do you change front fog light bulbs on 2005 vw golf tdi 2.0?
Being that you don't need them, why bother, it's summer.
http://www.golfmkv.com/forums/showthread鈥?/a>
seems like you'll need a torq screwdriver
How do you change front fog light bulbs on 2005 vw golf tdi 2.0?
Being that you don't need them, why bother, it's summer.
Fiat bravo fog lights not working?
hey, i got a fiat bravo and the front left fog light doesnt work, the right one and rear ones work fine...ive changed the bulb from halfords they said it isnt the bulb...ive even checked the fuses...still not working does anyone know if it could be an electical fault? if it is...does anyone have any ideas on how 2 fix it? thanks
Fiat bravo fog lights not working?
Get a multimeter and start tracing the wires back.
If you have 12v's getting to the bulb but no light then you have a bad earth.
If no 12v at bulb then trace it back to thru the loom to the relay/fusebox. I'd bet its a broken wire or bad connection.
Hope this helpsget your ex girlfriend back2 migrating existing portal
Fiat bravo fog lights not working?
Get a multimeter and start tracing the wires back.
If you have 12v's getting to the bulb but no light then you have a bad earth.
If no 12v at bulb then trace it back to thru the loom to the relay/fusebox. I'd bet its a broken wire or bad connection.
Hope this helps
Help in Acura TSX fog light?
I m currently driving a 06 Acura Tsx. I m looking for fog light bulbs. I had changed the factory fog light to a (Halo H11 with 4500K xenon plasma blue 12V100W). It worked out fine, until the bulb burnt out.
Now, i m looking for a new one. But i have a question about that. Can i use other H11 bulb lights such as those with 5000k, 7500k, 8000k and 8500k?
Thank You.
Help in Acura TSX fog light?
it depnds if you got just a normal bulb or a HID setup in the fog. Most normal bulbs will burn out because the how the voltage runs from the car to the bulb, its slightly off and causes it to blow.
a more permanent solution would be to get a HID kit for the fogs, and run some luminx vinyl over the bolb cover and you will get a bright yellow glow out of the fogs, and they will actually be usable as fogs.
usually you want something more around 4300K like stock for good light output. any high and you are going into the ultra violet range, where its going to be no use to use, especially as a fog. Especially as fogs if you go bright white and blue their going to be totally useless. you want a more yellow color with the fogs.
Help in Acura TSX fog light?
yes
Yes
Now, i m looking for a new one. But i have a question about that. Can i use other H11 bulb lights such as those with 5000k, 7500k, 8000k and 8500k?
Thank You.
Help in Acura TSX fog light?
it depnds if you got just a normal bulb or a HID setup in the fog. Most normal bulbs will burn out because the how the voltage runs from the car to the bulb, its slightly off and causes it to blow.
a more permanent solution would be to get a HID kit for the fogs, and run some luminx vinyl over the bolb cover and you will get a bright yellow glow out of the fogs, and they will actually be usable as fogs.
usually you want something more around 4300K like stock for good light output. any high and you are going into the ultra violet range, where its going to be no use to use, especially as a fog. Especially as fogs if you go bright white and blue their going to be totally useless. you want a more yellow color with the fogs.
Help in Acura TSX fog light?
yes
Yes
How do i change the front fog lamp bulbs on my peugeot 406?
how do i change the blown front fog light on my 2000 peugeot 406, lx they look tough to get to
How do i change the front fog lamp bulbs on my peugeot 406?
if it is the same as the 206 then you change the bulb from inside the wheel arch.
turn the wheels to full lock away from the bulb you are going to change.
there is a flap in the plastic arch cover pull it from the bottom and it hinges upwards.
you then turn the plastic cap on the back of the fog light and pull it off.
pull the wire off the bulb,squeeze the top of the wire clip and pull back.
the bulb can be pulled out of the fog light and the new one inserted.
fitting is the reverse,it should only take you 10-20 minutes max.
How do i change the front fog lamp bulbs on my peugeot 406?
have a look in the wheel arch there might be a nut you can undo.
If it's anything like a Citroen I used to have, you can't just change the bulbs; it's in a sealed unit.
You have to buy a complete foglight unit from the dealer. Specially designed to rip you off.
Don't bother it will save you blinding the oncoming traffic with them. However if you insist they are probably got at from behind the bumper so you will have to go under the car and unclip them. You may of course find that the lamp is removed rather like the headlamp and is held in by a clip.
Step 1: smash out the lenses of the fog lamps with a hammer
Step 2: replace blown bulbs
How do i change the front fog lamp bulbs on my peugeot 406?
if it is the same as the 206 then you change the bulb from inside the wheel arch.
turn the wheels to full lock away from the bulb you are going to change.
there is a flap in the plastic arch cover pull it from the bottom and it hinges upwards.
you then turn the plastic cap on the back of the fog light and pull it off.
pull the wire off the bulb,squeeze the top of the wire clip and pull back.
the bulb can be pulled out of the fog light and the new one inserted.
fitting is the reverse,it should only take you 10-20 minutes max.
How do i change the front fog lamp bulbs on my peugeot 406?
have a look in the wheel arch there might be a nut you can undo.
If it's anything like a Citroen I used to have, you can't just change the bulbs; it's in a sealed unit.
You have to buy a complete foglight unit from the dealer. Specially designed to rip you off.
Don't bother it will save you blinding the oncoming traffic with them. However if you insist they are probably got at from behind the bumper so you will have to go under the car and unclip them. You may of course find that the lamp is removed rather like the headlamp and is held in by a clip.
Step 1: smash out the lenses of the fog lamps with a hammer
Step 2: replace blown bulbs
How do i find the fuse for the fog lights on top of my 2003 jeep liberty?
i have a 2003 jeep liberty renegade. it has a light bar on top with 4 fog lights. the lights do not work. in the owners manual the fuse diagram has a fuse for the front fog lights(below the headlights) and for the rear headlights. There is not a fuse on the diagram for the light bar and i dont know what to do. How do i find the fuse? Or do i need to change the bulbs, because the button on the inside says that the lights are on when you press it but the lights do not turn on.
Changing Fogs to High Beams?
I'm buying a 2010 chevy camaro and was wanting best possible lights and was wondering... ok here goes im going to put in hid head lights but since they are mainly straight light i want to take the fog lights out and install high beams in there place the would be pointed lower so no hazard to other driver but my question is can i do it and how?
Thanks.
Changing Fogs to High Beams?
no illegal in most states
Thanks.
Changing Fogs to High Beams?
no illegal in most states
I got a 2000 pontiac grand am and my speedometer lights wont come on.and i checked da fuse any sugestions?
I changed my radio on my 2000 pontiac grand am, and now the lights on my speedometer, and fog light switch and light won't. Come on but all my others lights work I checked the fuses and took the radio out just to see if that was the problem but still nothing does any one have an idea or a suggestion?
I got a 2000 pontiac grand am and my speedometer lights wont come on.and i checked da fuse any sugestions?
well you might have blown the bulb light in the dash.Duvet cover designers research reduce or control it
I got a 2000 pontiac grand am and my speedometer lights wont come on.and i checked da fuse any sugestions?
well you might have blown the bulb light in the dash.
How do change the fog light bulb on my 2000 alero?
my answer is try to check it out first on auto repair shop..
How do change the fog light bulb on my 2000 alero?
Remove the wheel housing splash shield and then you can get to the electrical connector....
How do change the fog light bulb on my 2000 alero?
Remove the wheel housing splash shield and then you can get to the electrical connector....
1999 camaro z28 fog light bulb?
im getting ready to change my fog light because one is burned out but i dont know what kind of bulb to put in the fog light and how to do it. can some1 tell me what type of bulb to put in and how to do it.
1999 camaro z28 fog light bulb?
Check the book at the parts store but the bulb size should be 894
1999 camaro z28 fog light bulb?
take the bulb out take to auto parts store
1999 camaro z28 fog light bulb?
Check the book at the parts store but the bulb size should be 894
1999 camaro z28 fog light bulb?
take the bulb out take to auto parts store
To turn on the head lights you turn the knob on your left once ?
I'm not sure, when i turn on my headlights, i can barely see, it looks really dim , but then a while back when my bf was driving my car it looked brighter. Am i turning on the lights right? How do you turn on fog lights, im thinking thats what im doing wrong? Or is it that my lights are going out and i need to change them?
To turn on the head lights you turn the knob on your left once ?
turn the knob all the way (twice). if you need your brights, turn the knob all the way %26amp; push the lever forward to lock it into position.
check the lights out at your local gas station, they aught to know %26amp; they will advise you
To turn on the head lights you turn the knob on your left once ?
you should not be driving if you cant even turn on the lights
car truck or van? ford chev dodge and import ?
made by fischer price ?
FIRST MAK ESURE YOUR WINDOWS ARE DOWN , AND CHECK TO SEE IF YOU HAVE ENOUGH BLINKER FLUID ,
THEN TURN THE WHEELS TO THE LEFT WHILE YOU ARE GOING 75 IN A 25 , THEN SLAM ON THE BRAKES , IF YOU SEE A COP , RUN , RUN AND RUN AS FAST AS YOU CAN , DO NOT LET THEM KNOW ABOUT THE BODIES IN THE TRUCK , ONCE YOU HAVE DONE THIS AND YOU ARE IN A DARK SECLUDES AREA , THEN TWIST YOUR KNOB IF YOU CA N , THIS SHOULD DO THE TRICK OR TRICKS
This would depend on the year and make of the car. Most cars have a separate switch for the fog lights with an automatic shut off feature that turns the fog lights off when you are using the bright lights. I would consult the operators manual and determine where the switch is for the fog lights and whether or not there is an override for this feature.
Depends on the vehicle. You may be running on the dome light! Other vehicles (older ones) you'd pull the knob out.
If the dimmer switch in on the steering wheel, be careful you don't get your legs tangled.
Start your car, and turn the light switch until it stops.
You should now see your lights on the surface in front of you--garage door, apt. wall--so pull back on the turn-signal lever, and see if you still have two lights.
Look around the dashboard for the driving light switch (usually a pictogram of lights with lines in frront of them), and turn them on to see if they work. If your brights are on, the lights will not work, so pull the turn signal stalk again to lower them.
If at any time you have one headlight, or the driving-lights (fog lights are yellow) don't work, then you have a bad bulb.
Take your car to the dealer, or have your bf do the work, because it may be more than changing a bulb, depending on the age and make of your car. Here's why:
Look at the headlights during the daytime with them off, and see if they look cloudy or wet inside. Unfortunately, the type with the %26quot;simple to change%26quot; bulb tends to get terminal %26quot;fog-up/wetness%26quot; after about five years, and has to be replaced. Thsi may be why the lights look dimmer.
If you haven't found a problem so far, get back in the car, and turn the key to the on position without starting it, then look at the volt gauge: it should always read above 11, and the closer to 14 the better.
Start the engine, and check the volt guage again: if it is 13-14, then it's a battery problem (1 or more dead cells). If it's below 13, then its an alternator problem.
I've dealt with all these problems. I've been where you are, and that's why this email is so long.
First, What kinda car is it? Second, In Oklahoma it's illegal to have fog lights on. Also, If you don't know how to turn them on don't drive.
reach into the glove box and pull out the owners manual it will explain about the functions of all the knobs and levers read it before you ever move your car.
Hi, on most european car,the left lever is used for firstly cornering--- up and down for right and left cornering),----and secondly for headlights, dim for middle position, forward for full--used for highway/dark areas and backward for intermitent full headlights(Like a Signal) .
Now the knob situated at the end of the left lever have position 0, meaning no corner lamps and no dim/fog lights. Position 1(Turning once), meaning you can have only corner lamps front and rear one(including your rear number plate) and fog lights if you switch on the fog light switch(Normally situated on the dash board). Then position 2(Turning knob twice), will englobe position 1 function and main headlights(Dim if lever is in the middle...full if lever is pushed forward...and intermitent full if lever is pulled backward and released).
Now if you have switched on your headlights by turning the knob on your left twice, and that you are on idle speed or engine stopped, the light intensity will not be the same as when you are accelerating above 1000 rpm. Now, it is always advised to start the engine and then to switch on the headlights just to avoid draining energy from your battery uselessly.
If you have followed the steps and do not see any headlights or fog lights, this means that you must have either blow fuses, or bad relays...Now is everything lights and you are still not satisfied with your headlights, either take your car to an electrician for a general check on the state of your wiring and state of the headlights reflectors...and if everything is ok ,you can use special headlights bulbs(Xenox type) for better night vision.
To turn on the head lights you turn the knob on your left once ?
turn the knob all the way (twice). if you need your brights, turn the knob all the way %26amp; push the lever forward to lock it into position.
check the lights out at your local gas station, they aught to know %26amp; they will advise you
To turn on the head lights you turn the knob on your left once ?
you should not be driving if you cant even turn on the lights
car truck or van? ford chev dodge and import ?
made by fischer price ?
FIRST MAK ESURE YOUR WINDOWS ARE DOWN , AND CHECK TO SEE IF YOU HAVE ENOUGH BLINKER FLUID ,
THEN TURN THE WHEELS TO THE LEFT WHILE YOU ARE GOING 75 IN A 25 , THEN SLAM ON THE BRAKES , IF YOU SEE A COP , RUN , RUN AND RUN AS FAST AS YOU CAN , DO NOT LET THEM KNOW ABOUT THE BODIES IN THE TRUCK , ONCE YOU HAVE DONE THIS AND YOU ARE IN A DARK SECLUDES AREA , THEN TWIST YOUR KNOB IF YOU CA N , THIS SHOULD DO THE TRICK OR TRICKS
This would depend on the year and make of the car. Most cars have a separate switch for the fog lights with an automatic shut off feature that turns the fog lights off when you are using the bright lights. I would consult the operators manual and determine where the switch is for the fog lights and whether or not there is an override for this feature.
Depends on the vehicle. You may be running on the dome light! Other vehicles (older ones) you'd pull the knob out.
If the dimmer switch in on the steering wheel, be careful you don't get your legs tangled.
Start your car, and turn the light switch until it stops.
You should now see your lights on the surface in front of you--garage door, apt. wall--so pull back on the turn-signal lever, and see if you still have two lights.
Look around the dashboard for the driving light switch (usually a pictogram of lights with lines in frront of them), and turn them on to see if they work. If your brights are on, the lights will not work, so pull the turn signal stalk again to lower them.
If at any time you have one headlight, or the driving-lights (fog lights are yellow) don't work, then you have a bad bulb.
Take your car to the dealer, or have your bf do the work, because it may be more than changing a bulb, depending on the age and make of your car. Here's why:
Look at the headlights during the daytime with them off, and see if they look cloudy or wet inside. Unfortunately, the type with the %26quot;simple to change%26quot; bulb tends to get terminal %26quot;fog-up/wetness%26quot; after about five years, and has to be replaced. Thsi may be why the lights look dimmer.
If you haven't found a problem so far, get back in the car, and turn the key to the on position without starting it, then look at the volt gauge: it should always read above 11, and the closer to 14 the better.
Start the engine, and check the volt guage again: if it is 13-14, then it's a battery problem (1 or more dead cells). If it's below 13, then its an alternator problem.
I've dealt with all these problems. I've been where you are, and that's why this email is so long.
First, What kinda car is it? Second, In Oklahoma it's illegal to have fog lights on. Also, If you don't know how to turn them on don't drive.
reach into the glove box and pull out the owners manual it will explain about the functions of all the knobs and levers read it before you ever move your car.
Hi, on most european car,the left lever is used for firstly cornering--- up and down for right and left cornering),----and secondly for headlights, dim for middle position, forward for full--used for highway/dark areas and backward for intermitent full headlights(Like a Signal) .
Now the knob situated at the end of the left lever have position 0, meaning no corner lamps and no dim/fog lights. Position 1(Turning once), meaning you can have only corner lamps front and rear one(including your rear number plate) and fog lights if you switch on the fog light switch(Normally situated on the dash board). Then position 2(Turning knob twice), will englobe position 1 function and main headlights(Dim if lever is in the middle...full if lever is pushed forward...and intermitent full if lever is pulled backward and released).
Now if you have switched on your headlights by turning the knob on your left twice, and that you are on idle speed or engine stopped, the light intensity will not be the same as when you are accelerating above 1000 rpm. Now, it is always advised to start the engine and then to switch on the headlights just to avoid draining energy from your battery uselessly.
If you have followed the steps and do not see any headlights or fog lights, this means that you must have either blow fuses, or bad relays...Now is everything lights and you are still not satisfied with your headlights, either take your car to an electrician for a general check on the state of your wiring and state of the headlights reflectors...and if everything is ok ,you can use special headlights bulbs(Xenox type) for better night vision.
How to change the fog light on Mercedes Benz ml430 year 2001?
you need to go under the car there are two screws that hold the bulb and the plastic holder. after that you should be able to disconnect the bulb from the housing. The screws were philips if i remember right also the book at the parts store was wrong so i had to go back i think they use a h1 or h4 i cant remember and it was not easy the first time i literally had to lift the vehicle of the ground with ramps so i had enough room to see what i was doing. There might be an easier way...
How do i change the fog light in a 2004 Hyundia Sonata.?
i need to know what kind of bulb i need. How do i get it out??
How do i change the fog light in a 2004 Hyundia Sonata.?
Stand directly in front of fog light, reach under bumper and screw off holding cap. Kind of a tight squeeze. But that is where you change it.odp.net charakterset shared web hosting
How do i change the fog light in a 2004 Hyundia Sonata.?
Stand directly in front of fog light, reach under bumper and screw off holding cap. Kind of a tight squeeze. But that is where you change it.
Oldsmobile Alero Fog Light Bulb?
How do you change the fog light bulbs on a 2001 Oldsmobile Alero?
Nothing is in the manual.
Oldsmobile Alero Fog Light Bulb?
they turn out and unplug
Nothing is in the manual.
Oldsmobile Alero Fog Light Bulb?
they turn out and unplug
How to change a fog light bulb on a 2003530i bmw?
jack up the front, remove the plastic splash gaurds from underneath and it should be right there. If there trim around the front of the light then you may be able to take the trim off and replace from the front
How do you change the fog light on a 2001 740il bmw?
I believe there is a slot right there next to the fog light...you take a long screwdriver and press into that slot/hole and the fog light just pops out pretty as you please.
How do you change the fog light on a 2001 740il bmw?
take it to the dealer
How do you change the fog light on a 2001 740il bmw?
take it to the dealer
How do you change a fog light bulb on a 1997 saturn SC2?
You will need to reach from under the cars front bumper disconnect the wire harness and then turn the bulb clockwise to remove it .......remember not to touch the new bulb with your fingers.
Does anyone know how to change a fog light bulb on an olds aurora?
passengers side:)
Does anyone know how to change a fog light bulb on an olds aurora?
just make sure it is not a halogen and do not touch it, if you do, it will burn out fast like in a minute or two
good luck
an Old Aurora MMmm..not bad
smileget ride of my dry skin database
Does anyone know how to change a fog light bulb on an olds aurora?
just make sure it is not a halogen and do not touch it, if you do, it will burn out fast like in a minute or two
good luck
an Old Aurora MMmm..not bad
smile
96 eclipse fog lights
i have a 96 eclipse gst spyder and i put the front end of a 99 eclpse and i wanna hook up the fog lights that im going to order will they plug in or will i have to change the plug in's.
the thing i wanna know is are the plugs in from a 95-96 differnet then a 97-99 fog lights
96 eclipse fog lights
i don't know for sure right off the top of my head, but all i can say is find a forum site where all they talk about are dsms. try dsmtuners.com and they should be able to help you out.
(UPDATE!)
I just got done looking at the car information website that i have at school (Uti) the website we have here at school is called alldata.com and by looking at the electrical diagrams, the 96 eclipse has a different fog light connector then the 97-99, if you were able to change the connections over to the newer style then there would be no problem with anything. but changing them over would be the interesting part
the thing i wanna know is are the plugs in from a 95-96 differnet then a 97-99 fog lights
96 eclipse fog lights
i don't know for sure right off the top of my head, but all i can say is find a forum site where all they talk about are dsms. try dsmtuners.com and they should be able to help you out.
(UPDATE!)
I just got done looking at the car information website that i have at school (Uti) the website we have here at school is called alldata.com and by looking at the electrical diagrams, the 96 eclipse has a different fog light connector then the 97-99, if you were able to change the connections over to the newer style then there would be no problem with anything. but changing them over would be the interesting part
How do i change the fog light on a suzuki verona?
It would be easiest if the car was up in the air but you can also do it on the ground. Underneath the car behind the front bumper there is black plastic covering the engine area. Remove the plastic. You should now see the back of the fog light. Disconnect the wire that is connected to the bulb. Twist the bulb and pull out. Install new bulb and reconnect the wire. and install plastic cover.
Dodge Stratus Fog light bulb?
How do you change the fog light bulb on a 2003 dodge stratus. Do you have to get under the front bumper?
Dodge Stratus Fog light bulb?
The fog light lense has two screws holding it to the bumper. You should be able to remove the screws and the housing comes out and you should be able to remove the bulb that way. The headlights are pretty much the same way but with bolts attached to the radiator support.
Dodge Stratus Fog light bulb?
2-door or 4-door
remove the two screws that hold it on and remove it ,you can get to it that way ,those are simple to change out,any parts store will have the replacement bulb for it also,good luck.
Dodge Stratus Fog light bulb?
The fog light lense has two screws holding it to the bumper. You should be able to remove the screws and the housing comes out and you should be able to remove the bulb that way. The headlights are pretty much the same way but with bolts attached to the radiator support.
Dodge Stratus Fog light bulb?
2-door or 4-door
remove the two screws that hold it on and remove it ,you can get to it that way ,those are simple to change out,any parts store will have the replacement bulb for it also,good luck.
Thursday, September 15, 2011
How to change fog light bulb on 1999 9-3?
They have been out since I purchased the vehicle back in March but am finally looking to get them working again. H1 bulbs correct? In addition to a how to, does anyone recommend a certain brand for longevity?
How to change fog light bulb on 1999 9-3?
Yes it is an H1 bulb. We use Osram/Sylvania 64150 and have quite good life from them. To replace you will have to remove the plastic splash pans from under the front valance area, a series of 8mm headed screws. Then you will see the bottom of the fog / driving light housing. Remove the bulb cover cap and remove retainer to drop the bulb out. When installing the new bulb make very sure you DO NOT touch the glass portion of the bulb with your bare fingers. The oil from your fingers will burn into the glass and cause a hot spot that will cause premature failure of the bulb. This holds true for all Halogen bulbs no matter the application. Be careful with the bulb socket as it is aim-able and will break at its pivots if you force it into place. Hope this helps, Al.
How to change fog light bulb on 1999 9-3?
Yes it is an H1 bulb. We use Osram/Sylvania 64150 and have quite good life from them. To replace you will have to remove the plastic splash pans from under the front valance area, a series of 8mm headed screws. Then you will see the bottom of the fog / driving light housing. Remove the bulb cover cap and remove retainer to drop the bulb out. When installing the new bulb make very sure you DO NOT touch the glass portion of the bulb with your bare fingers. The oil from your fingers will burn into the glass and cause a hot spot that will cause premature failure of the bulb. This holds true for all Halogen bulbs no matter the application. Be careful with the bulb socket as it is aim-able and will break at its pivots if you force it into place. Hope this helps, Al.
How do i change the fog light to a '04 pontiac grand am?
jack the frontend of the car up and crawl underneath and there is a plastic shield that protects the fog light that has to be moved out of the way and then you can see what you have to do, the bulb just twists out of the light, just make sure you don't touch the new bulb when re-installing or it will burn out quicker.
How do i change the fog light to a '04 pontiac grand am?
from under the bumper on the backsideittwit graphics animation
How do i change the fog light to a '04 pontiac grand am?
from under the bumper on the backside
Fog Lights Not Working?
I recently had a new battery installed in my car as well as a timing belt. 3 days later I noticed that one of the fog lights and headlights on the driver side were not working, I hadn't driven the car at night since the battery replacement. Is the lights not working connected to the battery change in any way? I drive a Toyota Corolla 2003. Thanks!
Fog Lights Not Working?
I had that problem with my fog lights when I installed my radio. The battery has something to do with it.
Fog Lights Not Working?
They were burned out before the repairs were done.
Fog Lights Not Working?
I had that problem with my fog lights when I installed my radio. The battery has something to do with it.
Fog Lights Not Working?
They were burned out before the repairs were done.
Anyone know how to replace fog light bulbs on a 1998 Grand Prix Gt?
Does anyone know how to change the fog log bulbs on 1998 Grand Prix Gt? If you have a link to a website with or without pictures would be if better! Easy 10 points!!
p.s Yes I've already check the car manual..and no its not in there!
Anyone know how to replace fog light bulbs on a 1998 Grand Prix Gt?
jack the front of the car up and crawl under the front and you will see plastic covering over the bottom of the foglight, pull it out of the way and then you will be able to see the back of the foglight, just either pull or twist the connector out and unplug the bulb, a new bulb is about $12 at the partstore.
p.s Yes I've already check the car manual..and no its not in there!
Anyone know how to replace fog light bulbs on a 1998 Grand Prix Gt?
jack the front of the car up and crawl under the front and you will see plastic covering over the bottom of the foglight, pull it out of the way and then you will be able to see the back of the foglight, just either pull or twist the connector out and unplug the bulb, a new bulb is about $12 at the partstore.
Hi,how i can turn on fog light in hummer h2 without any changing !?
Power to separate switch then to fog light on the primary wire before the light.
Fog lights, on a ford focus 2000?
im looking to change the bulbs on my front spot/fog lights on a ford focus 2000, but am unable to figure out how to get the bulb out, can you just take the bulb out or do you have to take the whole light out, if so how do you do either of these things?
Fog lights, on a ford focus 2000?
you take the bulb and bulb holder out of the light casing it usually has retainer clips holding the casing tight, pop them off and take the bulb out make sure you have the right bulb though, take it to a garage for replacement, good luck.
Fog lights, on a ford focus 2000?
ur mom urm om
Fog lights, on a ford focus 2000?
you take the bulb and bulb holder out of the light casing it usually has retainer clips holding the casing tight, pop them off and take the bulb out make sure you have the right bulb though, take it to a garage for replacement, good luck.
Fog lights, on a ford focus 2000?
ur mom urm om
How to change 1999 jaguar xj8 fog lamp bulbs?
Id rather not travel to a dealer, and iv changed all the bulbs but i cant get to fog lights on the bottom
How to change 1999 jaguar xj8 fog lamp bulbs?
If you have to ask on YA you better take it to a qualified mechanic. If you live far away from the mechanic ask a mechanical minded friend or electrician for help.control panel buttons spots on dogs skin
How to change 1999 jaguar xj8 fog lamp bulbs?
If you have to ask on YA you better take it to a qualified mechanic. If you live far away from the mechanic ask a mechanical minded friend or electrician for help.
How do I change a fog light on a dodge neon sport?
There's a retaining bolt on the top front of the fog light that you have to remove. Then you remove the fog light cover forward and replace the bulb behind it. Should be an easy job, good luck.
How do I change a fog light on a dodge neon sport?
Thanks so much. Accomplished the Job!
How do I change a fog light on a dodge neon sport?
Thanks so much. Accomplished the Job!
Report Abuse
Do i need to change my wiring harness on 07 hhr to add factory fog lights if mine didn't come with any?
true jsut run a new wire but make sure to include a relay so you are not drawing off of the original lights this will lower the intensity kindof defeating the purposes
Do i need to change my wiring harness on 07 hhr to add factory fog lights if mine didn't come with any?
just run a new wire for lights
Do i need to change my wiring harness on 07 hhr to add factory fog lights if mine didn't come with any?
just run a new wire for lights
How to change the bulb on lower fog light on 1994 Subaru Impreza?
How do I remove the casing so I can get to the bulb? Do I have to take off the bumper?
How to change the bulb on lower fog light on 1994 Subaru Impreza?
on most models you will have two 8mm headed bolts i believe both on the bottom of the light assembly remove them and pull the Assembly out then you can just remove the bulb by twisting it counter clock wise then reverse to reinstall
simon
How to change the bulb on lower fog light on 1994 Subaru Impreza?
on most models you will have two 8mm headed bolts i believe both on the bottom of the light assembly remove them and pull the Assembly out then you can just remove the bulb by twisting it counter clock wise then reverse to reinstall
simon
Can i install fog lights on a 2010 nissan altima coup, the 2.5?
the 3.5 has them standard, but the 2.5 does not have punch outs for them, i keep finding fog lights with harnesses... but if my car doesnt have punch outs i dont see how i would be able to install them, do i have to change my whole bumper? or do the after markets somehow click over the bumper i currently have, or wtv! just please help please! thanks
Can i install fog lights on a 2010 nissan altima coup, the 2.5?
from what i have heard and seen on the altima forums, there is a certain section of the bumper that is replaced to create an opening for the fog lights. if you go to your local dealership they would be able to order the fog light installation kit for you. i would also recommend checking www.courtesyparts.com because they have great prices for genuine nissan accessories
Can i install fog lights on a 2010 nissan altima coup, the 2.5?
Only factory fog lights will function with the car's Body Control Module (BCM) and Intelligent Power Distribution Module, (IPDM) There is a fog light kit available it will come with another headlight turnsignal stalk with the rotary switch for fog lights also fog light bumper inserts. Factory fog lights are a $310 option see %26quot;nissanusa.com%26quot; Good Luck.
Yes you can
but if you aren't pre wired it can be a pain in the ***, if you are then its simple plug and play
no you don't have to change out your whole bumper... Just get OEM ones they fit perfectly in the brackets and will last longer then cheap ebay or aftermaket ones.
http://www.nicoclub.com/
browse on here
or
http://www.nissanclub.com
yes it is possible. if you look at your front bumper you can see two holes on the bottom left and right corner. they are covered by a plastic circle. thats where the fog lights would go if you had them. if you go to your dealer or where ever you service your can they can insert the fog lights into those holes. it would prob cost around $150 for the parts.
Can i install fog lights on a 2010 nissan altima coup, the 2.5?
from what i have heard and seen on the altima forums, there is a certain section of the bumper that is replaced to create an opening for the fog lights. if you go to your local dealership they would be able to order the fog light installation kit for you. i would also recommend checking www.courtesyparts.com because they have great prices for genuine nissan accessories
Can i install fog lights on a 2010 nissan altima coup, the 2.5?
Only factory fog lights will function with the car's Body Control Module (BCM) and Intelligent Power Distribution Module, (IPDM) There is a fog light kit available it will come with another headlight turnsignal stalk with the rotary switch for fog lights also fog light bumper inserts. Factory fog lights are a $310 option see %26quot;nissanusa.com%26quot; Good Luck.
Yes you can
but if you aren't pre wired it can be a pain in the ***, if you are then its simple plug and play
no you don't have to change out your whole bumper... Just get OEM ones they fit perfectly in the brackets and will last longer then cheap ebay or aftermaket ones.
http://www.nicoclub.com/
browse on here
or
http://www.nissanclub.com
yes it is possible. if you look at your front bumper you can see two holes on the bottom left and right corner. they are covered by a plastic circle. thats where the fog lights would go if you had them. if you go to your dealer or where ever you service your can they can insert the fog lights into those holes. it would prob cost around $150 for the parts.
I cant get my fog lights on?
Hi i changed the indicator bulb on the back left now my fog lights wont come on, there is a clip a bit like the telephone line clip but thinner that is there but there is no where for it to clip into someone said its for to add more to the car someone else said it could be the fuse but there is no fuse for the back lights only the front please can anyone help its really bugging me now thanks
I cant get my fog lights on?
well im an american auto mechanic are you talking about the rear fog light check your fuses first always start simple to hard you can buy a simple volt meter it a fancy way of saying a light to see if you have power going to the socket if no power check fuse if fuse is good check wires you have an open somewhere sometimes the copper connectors in the socket will corode and no contact will be made if you need more help just e-mail me
I cant get my fog lights on?
I think you need to ask the garage to take a physical look at it, maybe it is a simple mechanical thing.
By the time you find out whats wrong with it the Fog would have gone dont worry about fog lights some people dont even put there side or headlights on when the Weather gets bad they are suposed to by Law
Are you trying to turn the foglights on without the headlights on. Some cars foglights wont come on unless the headlights are on, try that.
If not, it is probably the fuse or the bulb.
Compare the lights at the side that you didn't change the indicator bulb on - it will show you where everything should go (it will probably be %26quot;the other way round%26quot;)
Hello
At a guess you've knocked the Earth wire off.
Andy Cdating to find african american hair
I cant get my fog lights on?
well im an american auto mechanic are you talking about the rear fog light check your fuses first always start simple to hard you can buy a simple volt meter it a fancy way of saying a light to see if you have power going to the socket if no power check fuse if fuse is good check wires you have an open somewhere sometimes the copper connectors in the socket will corode and no contact will be made if you need more help just e-mail me
I cant get my fog lights on?
I think you need to ask the garage to take a physical look at it, maybe it is a simple mechanical thing.
By the time you find out whats wrong with it the Fog would have gone dont worry about fog lights some people dont even put there side or headlights on when the Weather gets bad they are suposed to by Law
Are you trying to turn the foglights on without the headlights on. Some cars foglights wont come on unless the headlights are on, try that.
If not, it is probably the fuse or the bulb.
Compare the lights at the side that you didn't change the indicator bulb on - it will show you where everything should go (it will probably be %26quot;the other way round%26quot;)
Hello
At a guess you've knocked the Earth wire off.
Andy C
My 2006 gt fog lights wont turn on put in new headlights now no fog lights?
i changed my headlight bulbs and now all of a sudden my fog lights dont work
My 2006 gt fog lights wont turn on put in new headlights now no fog lights?
my answer is buy a new fuse...dude
My 2006 gt fog lights wont turn on put in new headlights now no fog lights?
try a new fuse that same thing happend to me with my jeep liberty
My 2006 gt fog lights wont turn on put in new headlights now no fog lights?
my answer is buy a new fuse...dude
My 2006 gt fog lights wont turn on put in new headlights now no fog lights?
try a new fuse that same thing happend to me with my jeep liberty
How do you change the OEM fog light bulb on a 2003 corolla?
Reach behind the light assembly. And remove bulb. It's either gonna have a locking ring that you twist off in a counter clockwise direction ...or its gonna have 2 spring wires holding the bulb to the assemly that you squeeze together and pull out on and then the bulb will come out
How to take off front headlight on a 2004 Maxima?
Trying to change fog lights and headlight bulbs and can't seen to get the headlight housing to come off, I see the 2 top screews but can't get to the bottom if there is one there.
How to take off front headlight on a 2004 Maxima?
More than likely there are 2 or 3 screws under the front bumper. But don't worry the front bumpers aren't that hard to remove.
How to take off front headlight on a 2004 Maxima?
More than likely there are 2 or 3 screws under the front bumper. But don't worry the front bumpers aren't that hard to remove.
How to remove front bumper to change fog light?
what kind of car?, most cars you have to jack the car up and crawl under the frontend and then you can get to the foglight without taking the front end off.
How to remove front bumper to change fog light?
The best way to find out is to get on your back and take a good look at it. It's probably mostly plastic pop rivets with a couple of bolts. It usually pays about an hour in a shop to remove and install. Expect double or triple as you haven't done it before.
How to remove front bumper to change fog light?
my partner used to be a mechanic and you very rarely need to remove a bumper, in fact he cant remember ever removing a bumper to change a foglight.but difficult to know without knowing what car you have.
Most makes of car have dedicated websites E.G Ford Escort RS owners club,try emailing them for specific advice.
These sites are what my partner uses for specific advice not covered in manuals.
would it not be better to remove light from bumper you replacing bulb or whol elight either way wouldnt need to remove bumper
it varies from car to car so without knowing what model exactly it will be pretty hard to tell you.
Generally the bumper is held on with bolts on the underside.
However, most of the time you don't need to remove the whole thing to change out a fog light.
If you need to change the light bulb just open the bonet and you can access the light from there or refer to your instruction manual.
How to remove front bumper to change fog light?
The best way to find out is to get on your back and take a good look at it. It's probably mostly plastic pop rivets with a couple of bolts. It usually pays about an hour in a shop to remove and install. Expect double or triple as you haven't done it before.
How to remove front bumper to change fog light?
my partner used to be a mechanic and you very rarely need to remove a bumper, in fact he cant remember ever removing a bumper to change a foglight.but difficult to know without knowing what car you have.
Most makes of car have dedicated websites E.G Ford Escort RS owners club,try emailing them for specific advice.
These sites are what my partner uses for specific advice not covered in manuals.
would it not be better to remove light from bumper you replacing bulb or whol elight either way wouldnt need to remove bumper
it varies from car to car so without knowing what model exactly it will be pretty hard to tell you.
Generally the bumper is held on with bolts on the underside.
However, most of the time you don't need to remove the whole thing to change out a fog light.
If you need to change the light bulb just open the bonet and you can access the light from there or refer to your instruction manual.
Why is my 2002 Hyundai Sonata keep blowing headlights/fog lights?
About once every 2-3 months I am changing some sort of light bulb on my car. It is either my headlight bulb, fog light bulb, or parking light bulb. About 3 or so weeks ago I replaced my passenger headlight bulb %26amp; drivers fog light bulb. This morning I get in my car and I now have my drivers side headlight out and the drivers side parking light. I love my car and NEVER had any issues other then this since I have owned the car with 89k+ miles and I bought her brand new. It is not under warranty anymore so that is why I am reaching out to my fellow yahooins :-)
Why is my 2002 Hyundai Sonata keep blowing headlights/fog lights?
One thing to consider, may be, that the bulbs you are buying, may be of a higher candle light power. Candle light refers to the intensity of the light, comming from the bulb. This term has been in use, since, the 1920's. The bulb or bulbs you buy, may look the same, but, may be higher in power, causing the wiring to get hot, thereby blowing your headlights. and, or foglamps. I have had this problem, myself. I tried untold numbers of headlights, and, foglamps, with no help, what so ever. Eventually, I had a friend,who, worked at the dealership, and, he told me, that certain items, like headlight bulbs, and, foglamp bulbs, and other special items, have to be bought right from the dealer, cause, these items, are made to fit, and work for your specific vehicle. He told me, that, the ones you buy at like Wal-Mart, and, the like, are no good... They work for a while, then, quit. They are just no good. He said, if they don't have the bulbs at the dealer, you should go to a autoparts store, like Carquest, Napa, Autozone,Advanced Auto, and, the like. Their bulbs are of a better quality, and, tthey last much longer. So, this I did, and, they are still in the vehicle, and, they have been in there, for two years, at least. No bulb will last forever, but, these come close. They cost a little more, but,in the long run, you are saving money, cause you aren't buying new ones, every 2-3 months. It has worked for me. With reguards to your car, you might want to consider looking into your fusebox,cause, somtimes, the more items, you have, on a fuse, can be a bit of a overload on that fuse. Something has to give. It has to either be the fuse, or, the headlight bulb, or, the foglamp bulb. Actually, the fuse should blow, before the headlight, or the foglamp, unless, the fuse for that item, has been replaced with a fuse, of a higher voltage, which, could be trouble. You see, a fuse is designed, to blow, incase of some kind of trouble, in your wiring system. Some people just replace the blown fuse, with one of a higher voltage. A fuse is actually rated, in, amps. Most popular are... 10, 15, 20, 25, 30, and so on. Say, if you have a item, that, takes a 20 amp fuse, and, it blows, most people will just put in a 30 amp fuse, instead. By doing this, they are defeating the purpose. Rather than blowing the fuse, like it should, it allows the current to keep flowing, thereby, starting a fire, in the wiring, cause something is getting too hot. That is what the fuse is for... To stop power to the particular item. It is always best to find out as to exactly what is causing the blown fuse, rather than replace it with one, of a higher amp. Many car fires start out as a fuse, that was of the wrong amp. It is possible, that you may have a shot in your wiring system, as well. You may also want to check your circuit breaker, for the headlights. This may need attention, as well. Good luck, and, I hope I've been of some help to you.
Why is my 2002 Hyundai Sonata keep blowing headlights/fog lights?
I used to own a 2004 Kia Optima. Loved it and would have still had it, but needed a larger car so I traded it in. Anyway, the pre '06 Optimas and Sonatas were %26quot;twins,%26quot; so a lot of the parts were the same. Anyway, my '04 Optima had a similar problem. I replaced more bulbs than I can think of in the couple of years I owned it. Don't know why but annoying as heck. Otherwise, was a great car.
You will have to check for any possible grounded or short in the car's electrical wirings. Check the relays and fuses, a shorted relay most commonly burn out bulbs. One problem would be the car's alternator, charging way up than the required voltage it should charge your batteries. You will require a multi tester to know the exact voltage of your car's electrical system or bring it to an auto electrical shop.
I would find out if there is a short some where in the wiring harness, check fuses thats all i can think of other than a power surge, but your car is about to new for that, good luck
sounds like you have a short in the harness, 10 yrs 100,000 mile warrarty its a hyundai unless you have more than 100,000 miles you didnt say good luck
the light bulbs that they put in cars today are s--t ! Plain and simple.share hotel rental fee streamreader
Why is my 2002 Hyundai Sonata keep blowing headlights/fog lights?
One thing to consider, may be, that the bulbs you are buying, may be of a higher candle light power. Candle light refers to the intensity of the light, comming from the bulb. This term has been in use, since, the 1920's. The bulb or bulbs you buy, may look the same, but, may be higher in power, causing the wiring to get hot, thereby blowing your headlights. and, or foglamps. I have had this problem, myself. I tried untold numbers of headlights, and, foglamps, with no help, what so ever. Eventually, I had a friend,who, worked at the dealership, and, he told me, that certain items, like headlight bulbs, and, foglamp bulbs, and other special items, have to be bought right from the dealer, cause, these items, are made to fit, and work for your specific vehicle. He told me, that, the ones you buy at like Wal-Mart, and, the like, are no good... They work for a while, then, quit. They are just no good. He said, if they don't have the bulbs at the dealer, you should go to a autoparts store, like Carquest, Napa, Autozone,Advanced Auto, and, the like. Their bulbs are of a better quality, and, tthey last much longer. So, this I did, and, they are still in the vehicle, and, they have been in there, for two years, at least. No bulb will last forever, but, these come close. They cost a little more, but,in the long run, you are saving money, cause you aren't buying new ones, every 2-3 months. It has worked for me. With reguards to your car, you might want to consider looking into your fusebox,cause, somtimes, the more items, you have, on a fuse, can be a bit of a overload on that fuse. Something has to give. It has to either be the fuse, or, the headlight bulb, or, the foglamp bulb. Actually, the fuse should blow, before the headlight, or the foglamp, unless, the fuse for that item, has been replaced with a fuse, of a higher voltage, which, could be trouble. You see, a fuse is designed, to blow, incase of some kind of trouble, in your wiring system. Some people just replace the blown fuse, with one of a higher voltage. A fuse is actually rated, in, amps. Most popular are... 10, 15, 20, 25, 30, and so on. Say, if you have a item, that, takes a 20 amp fuse, and, it blows, most people will just put in a 30 amp fuse, instead. By doing this, they are defeating the purpose. Rather than blowing the fuse, like it should, it allows the current to keep flowing, thereby, starting a fire, in the wiring, cause something is getting too hot. That is what the fuse is for... To stop power to the particular item. It is always best to find out as to exactly what is causing the blown fuse, rather than replace it with one, of a higher amp. Many car fires start out as a fuse, that was of the wrong amp. It is possible, that you may have a shot in your wiring system, as well. You may also want to check your circuit breaker, for the headlights. This may need attention, as well. Good luck, and, I hope I've been of some help to you.
Why is my 2002 Hyundai Sonata keep blowing headlights/fog lights?
I used to own a 2004 Kia Optima. Loved it and would have still had it, but needed a larger car so I traded it in. Anyway, the pre '06 Optimas and Sonatas were %26quot;twins,%26quot; so a lot of the parts were the same. Anyway, my '04 Optima had a similar problem. I replaced more bulbs than I can think of in the couple of years I owned it. Don't know why but annoying as heck. Otherwise, was a great car.
You will have to check for any possible grounded or short in the car's electrical wirings. Check the relays and fuses, a shorted relay most commonly burn out bulbs. One problem would be the car's alternator, charging way up than the required voltage it should charge your batteries. You will require a multi tester to know the exact voltage of your car's electrical system or bring it to an auto electrical shop.
I would find out if there is a short some where in the wiring harness, check fuses thats all i can think of other than a power surge, but your car is about to new for that, good luck
sounds like you have a short in the harness, 10 yrs 100,000 mile warrarty its a hyundai unless you have more than 100,000 miles you didnt say good luck
the light bulbs that they put in cars today are s--t ! Plain and simple.
I have a 1999 toyota Camry and i don't no how to replace the bulb in the fog lights.?
i have a 1999 toyota camry and i dont no how to change the bulb in the fog light. i can not figure out how to get to the bulb. if there is anyone that could help please tell me. thanx
I have a 1999 toyota Camry and i don't no how to replace the bulb in the fog lights.?
If they are like most factory installed fog lights, they are sealed and you can replace the bulb. You will have to replace the whole light. Better break into the savings because its a dealer item and you will be floored when you hear the price.
I have a 1999 toyota Camry and i don't no how to replace the bulb in the fog lights.?
If they are like most factory installed fog lights, they are sealed and you can replace the bulb. You will have to replace the whole light. Better break into the savings because its a dealer item and you will be floored when you hear the price.
Fog light bulb change in 2004 BMW 645ci?
I wanted to know how can i change the light bulb in the 2004 BMW 645ci fog lights?
I dont want to change the entire thing, just the bulbs. I don't want the yellow looking lights I want to have brighter ones put in. does anyone know how i can do this
Thank you :)
Fog light bulb change in 2004 BMW 645ci?
Take it your local BMW dealer
I was in a similar situation with my bmw
i got it replaced very cheap
I dont want to change the entire thing, just the bulbs. I don't want the yellow looking lights I want to have brighter ones put in. does anyone know how i can do this
Thank you :)
Fog light bulb change in 2004 BMW 645ci?
Take it your local BMW dealer
I was in a similar situation with my bmw
i got it replaced very cheap
Can you fit mk5 ford escort rear lights to a mk6 without any modification?
I am waiting on delivery of a smoothed boot for my girlfriends mk6 ford escort and have just realised hers has the fog light in the boot and the new one doesnt, can i just change the back lights for mk5 ones which have the rear fog in them without any more modification and if so are they the same connection?
Can you fit mk5 ford escort rear lights to a mk6 without any modification?
no you cant
Can you fit mk5 ford escort rear lights to a mk6 without any modification?
na it wont work it will look all lopsided
Can you fit mk5 ford escort rear lights to a mk6 without any modification?
no you cant
Can you fit mk5 ford escort rear lights to a mk6 without any modification?
na it wont work it will look all lopsided
How do i change my fog light in my 2006 hyundai sonata?
i can't see any screws?
How do i change my fog light in my 2006 hyundai sonata?
There are a few different ways. If you have an AutoZone, Carquest, NAPA, Advance, just about any auto parts store in your area and you purchase the light from them they will change it for you. I always watch to see how they do it so next time I remember how to do it. Have you checked your owners manual?
With my car and truck all you have to do is open the hood and there is bulbs in the back of the light. Ususally there isn't screws to remove anymore, just a bulb to change.
How do i change my fog light in my 2006 hyundai sonata?
Misstigeress, your anwser if not helpful. robert m is looking for an answer, not a guess. If it were as simple as recaing in and changing the bulb, he wouldn't be asking the question.
How do i change my fog light in my 2006 hyundai sonata?
There are a few different ways. If you have an AutoZone, Carquest, NAPA, Advance, just about any auto parts store in your area and you purchase the light from them they will change it for you. I always watch to see how they do it so next time I remember how to do it. Have you checked your owners manual?
With my car and truck all you have to do is open the hood and there is bulbs in the back of the light. Ususally there isn't screws to remove anymore, just a bulb to change.
How do i change my fog light in my 2006 hyundai sonata?
Misstigeress, your anwser if not helpful. robert m is looking for an answer, not a guess. If it were as simple as recaing in and changing the bulb, he wouldn't be asking the question.
Report Abuse
How do you change front wheel brg on ford escort td estate,also how to change bulb on front fog lights?
if you cant change a bulb then i dont want you to touch the bearing!!!
How do you change front wheel brg on ford escort td estate,also how to change bulb on front fog lights?
Front wheel bearings should be done by qualified mechanic, special tools needed. Fog light, simple but time consuming.
How do you change front wheel brg on ford escort td estate,also how to change bulb on front fog lights?
U need a bearing press to remove %26amp; fit a front wheel bearing. U also have to take off the hub to do it. Dont try it unless u know what u are doing.database get your ex girlfriend back2
How do you change front wheel brg on ford escort td estate,also how to change bulb on front fog lights?
Front wheel bearings should be done by qualified mechanic, special tools needed. Fog light, simple but time consuming.
How do you change front wheel brg on ford escort td estate,also how to change bulb on front fog lights?
U need a bearing press to remove %26amp; fit a front wheel bearing. U also have to take off the hub to do it. Dont try it unless u know what u are doing.
What is the best way to change a front fog light on a T reg peugeot 306?
I have changed the o/s/f with great difficulty but now need to change the n/s/f so the lenses match.
What is the best way to change a front fog light on a T reg peugeot 306?
Remove it when there is no fog
What is the best way to change a front fog light on a T reg peugeot 306?
Smash the hell out of it untll it falls out!
What is the best way to change a front fog light on a T reg peugeot 306?
Remove it when there is no fog
What is the best way to change a front fog light on a T reg peugeot 306?
Smash the hell out of it untll it falls out!
Electrical problem fog lights?
i have vectra w reg ls. ive been told they have pre installed wiring for front fogs i have changed the switch unit, fitted a relay and connected the fogs to the plugs in the bumper . but doesnt work doesnt seem to be any power at plugs that connect to fogs .? any ideas maybe im missing something?
Electrical problem fog lights?
Make sure you have a fuse installed on the circuit. Check your car manual for which fuse.
Electrical problem fog lights?
don't forget they only work when the main lights are on so try them with your dipped headlights on...
If the vehicle wasn't equipped with them from the factory the harness is not complete, there is a harness specifically for the fog lamps as well as relays and wiring in the dash and fuse panel. So best thing is to have a certified mechanic install them properly to avoid any problems down the road
Electrical problem fog lights?
Make sure you have a fuse installed on the circuit. Check your car manual for which fuse.
Electrical problem fog lights?
don't forget they only work when the main lights are on so try them with your dipped headlights on...
If the vehicle wasn't equipped with them from the factory the harness is not complete, there is a harness specifically for the fog lamps as well as relays and wiring in the dash and fuse panel. So best thing is to have a certified mechanic install them properly to avoid any problems down the road
I can't get to the inside of my fog lights.?
1991 Toyota Pickup, does anyone know how to get inside the front side lights to change the bulbs? It's set up in an odd way where you can unscrew the whole area but I can't get off the light cover. Any ideas?
I can't get to the inside of my fog lights.?
Once the screws are out the entire assy pops out as a unit. The bulb socket is installed in the rear of th unit. Usually is twist out. Half turn or less. Theres the bulb.
I can't get to the inside of my fog lights.?
i have no idea....but the haynes manual from autozone for only about 17.00 does...and it will shoe you along with everything else on it ....with pictures!!!!!!
good luck
I can't get to the inside of my fog lights.?
Once the screws are out the entire assy pops out as a unit. The bulb socket is installed in the rear of th unit. Usually is twist out. Half turn or less. Theres the bulb.
I can't get to the inside of my fog lights.?
i have no idea....but the haynes manual from autozone for only about 17.00 does...and it will shoe you along with everything else on it ....with pictures!!!!!!
good luck
How do i change the fog light in a 2004 Hyundia Sonata.?
i need to know what kind of lightbulb there is. How do i get it out??
How do i change the fog light in a 2004 Hyundia Sonata.?
just bring ur car to a hyundia car dealer place. they will change it for u for a cost but its worth it because you dont know what light bulb to use and how to change it so just bring it to a hyundia place.
How do i change the fog light in a 2004 Hyundia Sonata.?
TRY FINDING AN INDEPENDENT SHOP INSTEAD OF THE DEALER OR A CHAIN STORE BECAUSE YOU WILL BE OVERALL MORE PLEASED WITH THE FINDINGS AND THE SERVICE.
How do i change the fog light in a 2004 Hyundia Sonata.?
just bring ur car to a hyundia car dealer place. they will change it for u for a cost but its worth it because you dont know what light bulb to use and how to change it so just bring it to a hyundia place.
How do i change the fog light in a 2004 Hyundia Sonata.?
TRY FINDING AN INDEPENDENT SHOP INSTEAD OF THE DEALER OR A CHAIN STORE BECAUSE YOU WILL BE OVERALL MORE PLEASED WITH THE FINDINGS AND THE SERVICE.
Fog lights not working need help?
i have a 99 alero and only one fog light was working so i bought the other one . when i was changing it i must have short cicut the wires because the other turned of. I checked all the fuses and they are good. i also bought 2 new fog lights bulbs and they still did not work what else can i do or check?
Fog lights not working need help?
always replace headlights and fog lights in pairs. make sure headlights are not in highbeam, fog lights wont go on with highbeams on. if that doesn't work need to make sure power is getting to lights if not might be a bad switch
Fog lights not working need help?
you need a test light for this. check all the wires back an you will find the problemhair gel email
Fog lights not working need help?
always replace headlights and fog lights in pairs. make sure headlights are not in highbeam, fog lights wont go on with highbeams on. if that doesn't work need to make sure power is getting to lights if not might be a bad switch
Fog lights not working need help?
you need a test light for this. check all the wires back an you will find the problem
Does anyone know how to change the fog light bulbs on a 2002 Isuzu Rodeo?
I just can't seem to figure it out can someone please explain or provide a link??
Does anyone know how to change the fog light bulbs on a 2002 Isuzu Rodeo?
Go to Autozone and get a Haynes manual for your car. Trust me, it's worth it's weight in gold.
Does anyone know how to change the fog light bulbs on a 2002 Isuzu Rodeo?
Go to Autozone and get a Haynes manual for your car. Trust me, it's worth it's weight in gold.
How do you change the fog light bulb on a 1998 camaro Z28?
You'll have to get a Chiltons or Haynes manual for this if it isn't in the owners manual. It requires a little disassembly to get to it. I hate working on them. Too cramped. All day to change plugs.
Why are fog lights yellow? Does it really help to have them yellow? Does it matter where yoyr driving?
Does this change between the countryside and the city?
Why are fog lights yellow? Does it really help to have them yellow? Does it matter where yoyr driving?
Fog lights that are yellow tend to be better because they %26quot;cut through the fog%26quot; as some call it.
White lights tend to reflect off of fog, and thus isn't very efficient in the fog.
Try putting yellow glasses on and see the difference vs. clear glasses.
Why are fog lights yellow? Does it really help to have them yellow? Does it matter where yoyr driving?
the location of the lights is really what makes them %26quot;fog lights%26quot;. The yellow coloring might help slightly due to the fact that yellow light doesn't tend to diffract as much against the mist, but its the trajectory which makes them effective. The light would also reflect better off the lines in the middle of the road (obviously more lines in the city than the countryside).
The only difference between countryside and city driving would be that the density of the fog would be greater in the countryside as opposed to the city (greater amount of moisture).
Yellow is the most difficuly color for the human brain/eye to process - that is why it %26quot;stands out%26quot; more to us. Hence, the choice of markers and sticky notes everywhere.
Why are fog lights yellow? Does it really help to have them yellow? Does it matter where yoyr driving?
Fog lights that are yellow tend to be better because they %26quot;cut through the fog%26quot; as some call it.
White lights tend to reflect off of fog, and thus isn't very efficient in the fog.
Try putting yellow glasses on and see the difference vs. clear glasses.
Why are fog lights yellow? Does it really help to have them yellow? Does it matter where yoyr driving?
the location of the lights is really what makes them %26quot;fog lights%26quot;. The yellow coloring might help slightly due to the fact that yellow light doesn't tend to diffract as much against the mist, but its the trajectory which makes them effective. The light would also reflect better off the lines in the middle of the road (obviously more lines in the city than the countryside).
The only difference between countryside and city driving would be that the density of the fog would be greater in the countryside as opposed to the city (greater amount of moisture).
Yellow is the most difficuly color for the human brain/eye to process - that is why it %26quot;stands out%26quot; more to us. Hence, the choice of markers and sticky notes everywhere.
Peugeot 206 gti fog lights?
how do i change the front fog lights on my 206 gti?
Peugeot 206 gti fog lights?
There is a plastic flap on the inside of the wheel arch.Pull this open and you can get to the back of the fog lights.Pull the plug off the back of the light and undo the 3 nuts holding the light in place.The light then pulls backwards and out of the flap.The wheels have to be removed or put into full lock to do this.
Peugeot 206 gti fog lights?
There is a plastic flap on the inside of the wheel arch.Pull this open and you can get to the back of the fog lights.Pull the plug off the back of the light and undo the 3 nuts holding the light in place.The light then pulls backwards and out of the flap.The wheels have to be removed or put into full lock to do this.
How do i change the fog light bulb on my 2002 mercury sable?
not the whole assembly.. just the one light that went out.
How do i change the fog light bulb on my 2002 mercury sable?
Best answer you will get, go down to advance auto and purchase the haynes manual for your vehicle (20 bucks) and save a TON of money and time asking questions about things like bulbs. Good Luck!
How do i change the fog light bulb on my 2002 mercury sable?
if it is in the grill you will have to get behind it to gain access to the bulb and wire, the socket twists to the left to pull it out of the lense housing, then you can remove the old bulb and replace it with the new one ( with out touching the bulb )favorite recipe chicken Ideas for a Summer quilt layout
How do i change the fog light bulb on my 2002 mercury sable?
Best answer you will get, go down to advance auto and purchase the haynes manual for your vehicle (20 bucks) and save a TON of money and time asking questions about things like bulbs. Good Luck!
How do i change the fog light bulb on my 2002 mercury sable?
if it is in the grill you will have to get behind it to gain access to the bulb and wire, the socket twists to the left to pull it out of the lense housing, then you can remove the old bulb and replace it with the new one ( with out touching the bulb )
What does a Thai 2007 Ford Ranger use for its headlight and Fog light bulbs?
I would like to change the lights my Asian Ranger to HID's. What bulb type should I buy for the headlights and fog lights?
What does a Thai 2007 Ford Ranger use for its headlight and Fog light bulbs?
kragen.com
autozone.com
They'll take care of you
What does a Thai 2007 Ford Ranger use for its headlight and Fog light bulbs?
headlight: 9007
foglight: 9145
What does a Thai 2007 Ford Ranger use for its headlight and Fog light bulbs?
kragen.com
autozone.com
They'll take care of you
What does a Thai 2007 Ford Ranger use for its headlight and Fog light bulbs?
headlight: 9007
foglight: 9145
How do you change a fog light bulb on a 2007 Pontiac G5 GT?
I don't know how to change the bulb on my foglight of my 2007 pontiac g5 gt. It would be a great help if you could tell me! haha
How do you change a fog light bulb on a 2007 Pontiac G5 GT?
try to check it out first on auto repair shop...
How do you change a fog light bulb on a 2007 Pontiac G5 GT?
reach behind the bumper and there should be part of the assembly that turns and it will pop out and you have access to the bulb.
How do you change a fog light bulb on a 2007 Pontiac G5 GT?
try to check it out first on auto repair shop...
How do you change a fog light bulb on a 2007 Pontiac G5 GT?
reach behind the bumper and there should be part of the assembly that turns and it will pop out and you have access to the bulb.
How do you change the fog light bulbs in a 2003 Nissan Altima?
Remove the inner fender liner. Reach behind the airdam and turn the back of the housing counterclockwise, and replace bulb.
Fog lights on Nissan Pathfinder?
I have a 1999 Nissan Pathfinder and I need to change out the bulbs on the fog lights but i can't figure out how its done? any help would be great.
Fog lights on Nissan Pathfinder?
in the owners manual DIY section 8 page 26 there is a plastic piece that pops off and under that two philips bolts then two pegs on the other side pull it out the front turn it over unplug the wires and replace the bulb under the spring clip easy about ten minutes where there is light.
Fog lights on Nissan Pathfinder?
I don't know, but I recommend you buy a maintenance book for your car. My son bought one for his Jeep Cherokee and it changed his life and his pocket, because he did a lot of things impossible before.
I was looking for one book for my Nissan Xterra, but there are just for Pathfinder.
And you will save a lot of money avoiding Nissan's Techs..
Fog lights on Nissan Pathfinder?
in the owners manual DIY section 8 page 26 there is a plastic piece that pops off and under that two philips bolts then two pegs on the other side pull it out the front turn it over unplug the wires and replace the bulb under the spring clip easy about ten minutes where there is light.
Fog lights on Nissan Pathfinder?
I don't know, but I recommend you buy a maintenance book for your car. My son bought one for his Jeep Cherokee and it changed his life and his pocket, because he did a lot of things impossible before.
I was looking for one book for my Nissan Xterra, but there are just for Pathfinder.
And you will save a lot of money avoiding Nissan's Techs..
How to change fog light on 2006 Hyundai Sonata?
on the bottom side of the car under the fog light area there will be an inspection cover. it is held in place by two plastic trim clips. they will have what looks like a philips head on the screw. remove both of these then pull out the retainer (they are set up like a dry wall anchor). pull back the cover and unplug the bulb. twist the bulb counter clock wise to remove. install in reverse order.creating file does any ram fit on my computer
2006 lexus gs fog lights?
I looked at the car manl and it really did not say how to change the bulb on the fog light. Does anyone know how to change the fog lamp bulb. 2006 lexus gs
2006 lexus gs fog lights?
To get to the fog light bulbs, you will need to access the rear of the fog lights from within the front fender wells.
The inner liner is held in place by screws and is secured in place by some notched sections that are held in place on the inner fender. You will require to remove most of the screws up until 3/4 of way. If you are facing your fender, much like a watch, you will require to remove screws beginning at 08:00 o'clock until 14:00, this will allow the front fender housing to drop down and out of the way hence giving you access to the rear of the fog light.
Like most fog lights, they are of a screw left (or right, don't remember) and off they come.
good luck
2006 lexus gs fog lights?
take it to the dealer its a Lexus if you could afford a Lexus then you could afford there service
2006 lexus gs fog lights?
To get to the fog light bulbs, you will need to access the rear of the fog lights from within the front fender wells.
The inner liner is held in place by screws and is secured in place by some notched sections that are held in place on the inner fender. You will require to remove most of the screws up until 3/4 of way. If you are facing your fender, much like a watch, you will require to remove screws beginning at 08:00 o'clock until 14:00, this will allow the front fender housing to drop down and out of the way hence giving you access to the rear of the fog light.
Like most fog lights, they are of a screw left (or right, don't remember) and off they come.
good luck
2006 lexus gs fog lights?
take it to the dealer its a Lexus if you could afford a Lexus then you could afford there service
How do I change the fog light bulb on a 1996 Saab 900 S?
I cant figure out how to get the back cover off of the light. I havent completely removed the light from the car, but I can get to the back of it by removing the air breather box but I cant seem to figure out how to remove the black back cap from the light itself.
How do I change the fog light bulb on a 1996 Saab 900 S?
I am having the same problem. Typically, when I have issues, I go to www.thesaabsite.com and often find solutions. Today (24 DEC) I tried changing driver-side Fog light - it's not an easy task. The passenger may actually be easier, although it does have more screws. The grill does not require removal, but the turn-signal assembly has to. There are 2 screws directly under (beneath the bumper), but there is a third also. Soon as the weather breaks, I'll go ahead and remove a small portion of the under-bumper cover and give it another try. Go here: http://www.thesaabsite.com/93/93foglightreplacement.htm ... and read more. I imagine that the rates I have seen for a complete replacement of the FOG light ranged from $130-$176. Sounds a bit high, but it appears to be the variable average rate. I bought a spare bulb at a local auto parts store, but I am certain that the quality (brightness) would not be the same as a genuine part. Good luck. I hope I've been of some help.
How do I change the fog light bulb on a 1996 Saab 900 S?
I am having the same problem. Typically, when I have issues, I go to www.thesaabsite.com and often find solutions. Today (24 DEC) I tried changing driver-side Fog light - it's not an easy task. The passenger may actually be easier, although it does have more screws. The grill does not require removal, but the turn-signal assembly has to. There are 2 screws directly under (beneath the bumper), but there is a third also. Soon as the weather breaks, I'll go ahead and remove a small portion of the under-bumper cover and give it another try. Go here: http://www.thesaabsite.com/93/93foglightreplacement.htm ... and read more. I imagine that the rates I have seen for a complete replacement of the FOG light ranged from $130-$176. Sounds a bit high, but it appears to be the variable average rate. I bought a spare bulb at a local auto parts store, but I am certain that the quality (brightness) would not be the same as a genuine part. Good luck. I hope I've been of some help.
Audi A6 2001 Fog Lights, rear and front, replacing?
OK First of all I have a question I wanted to change the light bulb for the front fog lights on the bumper for my Audi A6, BUT what kind of bulb is it it looks huge when i took it off? Also The rear fog lights are under a carbon fiber plate near the license plate how do I remove it theirs no screws or any thing at all?
Audi A6 2001 Fog Lights, rear and front, replacing?
OK, this is tricky. You cannot get to the rear fog light (singular) from the outside. You must open the rear deck lid and remove the soft liner. The 2001 A6 is pecular in that in the US only the left lens is activated and in EU the right is activated. In model years 2002 and later they smartened up and both lenses are activated.
To remove the liner panel there are two sets of two screw pins. The first are obvious to find. The second set is behind the road hazard triangle. Take out this accessory to expose the second set of fasteners. After removing these the panel should snap out exposing the wiring harness and lamp assembly. Twist to remove from the housing and you now have access to replacing the lamp.
Audi A6 2001 Fog Lights, rear and front, replacing?
bring the big bulb to the parts store to match
rear fog lights??? never seen them
Audi A6 2001 Fog Lights, rear and front, replacing?
OK, this is tricky. You cannot get to the rear fog light (singular) from the outside. You must open the rear deck lid and remove the soft liner. The 2001 A6 is pecular in that in the US only the left lens is activated and in EU the right is activated. In model years 2002 and later they smartened up and both lenses are activated.
To remove the liner panel there are two sets of two screw pins. The first are obvious to find. The second set is behind the road hazard triangle. Take out this accessory to expose the second set of fasteners. After removing these the panel should snap out exposing the wiring harness and lamp assembly. Twist to remove from the housing and you now have access to replacing the lamp.
Audi A6 2001 Fog Lights, rear and front, replacing?
bring the big bulb to the parts store to match
rear fog lights??? never seen them
2008 Chevy Avalanche fog light bulb size?
I want to change the fog lights on my 2008 Chevy Avalanche to HID's and need to know the size of the bulb... I called a nearby dealership but they could not help me. Does anyone know the size? Thanks!
2008 Chevy Avalanche fog light bulb size?
Maybe this will help!
http://www.autozone.com/Ntt,Fog+light/sh…
2008 Chevy Avalanche fog light bulb size?
Maybe this will help!
http://www.autozone.com/Ntt,Fog+light/sh…
Change bulbs on 2004 Corolla S OEM fog lights?
I have an '04 Corolla S with the type H3 fog lamps installed (standard). I can crawl under and twist the back off as you would a headlight, but it has a wire attached to the bulb (this type of bulb doesn't come out with the twist off connector). I can't see up there, but can feel around. Does anyone know how to remove the bulb attached to the fog light or how to pop out the entire fog light?
Thanks!
Change bulbs on 2004 Corolla S OEM fog lights?
Hello Rice Burner lol I had that same problem it has a spring clip in it on a hinge. You don't need to remove it just squeeze it and, it will act like a door and open so you can pull the bulb out. Take care and Happy Driving...RobParameter.Add() how do ex smokers deal with
Thanks!
Change bulbs on 2004 Corolla S OEM fog lights?
Hello Rice Burner lol I had that same problem it has a spring clip in it on a hinge. You don't need to remove it just squeeze it and, it will act like a door and open so you can pull the bulb out. Take care and Happy Driving...Rob
How do I change the fog light bulb on my car?
Its a 2003 Nissan Maxima SE. Dont say check the manual because its not in there. : )
How do I change the fog light bulb on my car?
if it is the whole light assembly, usually there are just a couple of screws that hold the assembly in. if it just a bulb, then there should be a section that pulls out from the rear of the assembly to replace the bulb.
when you install it, make sure it is properly aligned!
How do I change the fog light bulb on my car?
if it is the whole light assembly, usually there are just a couple of screws that hold the assembly in. if it just a bulb, then there should be a section that pulls out from the rear of the assembly to replace the bulb.
when you install it, make sure it is properly aligned!
How do you change a fog light in a 97 Pontiac Montana?
It seems theres no way to access it does it screw out from the front or do you have to unscrew molding around the bottom to get to it?
How do you change a fog light in a 97 Pontiac Montana?
In 1997 they did not make a Montana they made the Trans Sport and if this is what to have they you will need to remove the (2) nuts from behind the bumper and pull the light out forward...and remove the lower splash shield as well.
How do you change a fog light in a 97 Pontiac Montana?
In 1997 they did not make a Montana they made the Trans Sport and if this is what to have they you will need to remove the (2) nuts from behind the bumper and pull the light out forward...and remove the lower splash shield as well.
How do I change a fog light bulb to a 95 Transam.?
The lens itself is fine. I just need to change the inside bulb.
How do I change a fog light bulb to a 95 Transam.?
check owner manuial
How do I change a fog light bulb to a 95 Transam.?
buy an auto repair manual for that model and year car. Either a Haynes or a Chilton. They cost between 20 and 25 dollars.
How do I change a fog light bulb to a 95 Transam.?
check owner manuial
How do I change a fog light bulb to a 95 Transam.?
buy an auto repair manual for that model and year car. Either a Haynes or a Chilton. They cost between 20 and 25 dollars.
How do I change the fog light bulb for a 2005 Nissan Altima?
I think I already have the right bulb. I'm not very Car savvy and really don't want to screw anything up. Instructions or a website will be very helpful.
How do I change the fog light bulb for a 2005 Nissan Altima?
You lay on the ground then access the back of the fog light by removing a couple screws under the side of the bumper cover then bend back the black plastic inner fender liner. Watch for the plastic clips falling off disconnect the electrical plug squeeze the square button in the side if the brown/or gray connector and pull off now twist the bulb out and with out touching the new bulb glass twist the new bulb in.hook up the power and test. Bend back the inner fender reinstall the clips and screws. Easy 10 minutes Good Luck
How do I change the fog light bulb for a 2005 Nissan Altima?
You lay on the ground then access the back of the fog light by removing a couple screws under the side of the bumper cover then bend back the black plastic inner fender liner. Watch for the plastic clips falling off disconnect the electrical plug squeeze the square button in the side if the brown/or gray connector and pull off now twist the bulb out and with out touching the new bulb glass twist the new bulb in.hook up the power and test. Bend back the inner fender reinstall the clips and screws. Easy 10 minutes Good Luck
Subscribe to:
Posts
(Atom)